Shop headings: New Spares | Used Spares | Accessories | Brands
Dimensions:
M16 x 1 threaded section, 8mm fuel pipe spigot
Manual square bodied fuel tap with nut, washer and filter. Fits left or right hand side of tank.
Off, on and reserve positions. Approved for use with fuel containing ethanol.
Availability varies on this part, check availability
14105400-z 14105400 GU14105400 14 10 54 00
1410 5400 1410.5400 14.10.54.00
£40.00
INC VAT
£33.33 EX VAT
Dimensions:
38cm long
Rear brakeline from splitter or proportioning valve to rear caliper fixed pipe. Also used as lower front right hand pipe to caliper fixed pipe on T3
Original type rubber brakeline with chunky galvanized ends
This part is due back in stock soon, call 01484 841395 to reserve yours
17657550
£40.00
INC VAT
£33.33 EX VAT
Dimensions:
Length 239mm, ,15mm tip to under hex head
Steel fixed rear brake pipe with threaded connectors at each end
Rigid brake pipe
1 in stock
17658650 GU17658650 17 65 86 50
1765 8650 1765.8650 17.65.86.50
£39.90
INC VAT
£33.25 EX VAT
Replacement pannier to frame lock for all Hepco and Becker panniers. This is the lock at the rear of the panniers that secures it to the pannier frame plate
Supplied with key, barrel, lock plate, rivets and fitting instructions. Includes pannier frame plate LUA70114
1 in stock
£39.60
INC VAT
£33.00 EX VAT
Dimensions:
9mm ID mounts, 168mm centres minimum, 250mm centres fully extended
Steering damper in black finish
Fits to original frame bracket
3 in stock
14530201-z 14530201 GU14530201 14 53 02 01
1453 0201 1453.0201 14.53.02.01
£39.00
INC VAT
£32.50 EX VAT
Dimensions:
720mm wide, 40mm rise, 22mm OD, knurled sections have 100mm centres and are 20mm wide
Pair of universal chromed handlebars, low rise
Not suitable for V65 GT, Mille GT or other models with wide handlebar clamps. Note wide spacing of knurled sections sits outside handlebar clamps on T3, V50 etc... - see dimensions if in doubt about suitability for your bike
1 in stock
£39.00
INC VAT
£32.50 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
This part is due back in stock soon, call 01484 841395 to reserve yours
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Dimensions:
44mm ID at carb, 30mm ID at engine inlet
Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)
Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters
This part is due back in stock soon, call 01484 841395 to reserve yours
£39.00
INC VAT
£32.50 EX VAT
Dimensions:
For 35mm forks
Chrome left hand headlight bracket
See SUA17700 for mounting rubbers (two required per side)
Sorry, this part is no longer available.
14496250-z 14496250 GU14496250 14 49 62 50
1449 6250 1449.6250 14.49.62.50
Sorry this item is out of production
Dimensions:
For 35mm forks
Chrome right hand headlight bracket
See SUA17700 for mounting rubbers (two required per side). NB the right hand bracket has a crease in the back of the tube
Sorry, this part is no longer available.
14496150-z 14496150 GU14496150 14 49 61 50
1449 6150 1449.6150 14.49.61.50
Sorry this item is out of production
Secure online shopping 
